FF/FL Testing
Fmin Testing
Corrective Grinding
navigation close
Allen Face Europe>

F-min Testing

  • F-min Testing
  • Fmin is the most advanced method available for gauging a floor’s ability to support wire- or rail-guided lift truck traffic in narrow aisle warehouses. The system directly controls future vehicle motions by limiting all six of the surface variables that affect hard-axle vehicle motions.


Recent Fmin Jobs

  • Abercrombie & Fitch Warehouse - Columbus OH (13 aisles x 70m)
  • Estee-Lauder Warehouse - Bristol PA (50 aisles x 35m)
  • Air-Gas Warehouse - Bristol PA (10 aisles x 65m)
  • Mizuno Warehouse - Atlanta GA (16 aisles x 30m)
  • Northwestern University Library Warehousee - Waukegan IL (4 aisles x 70m)
  • Qatar Foundation Offsite Warehouse - Doha QATAR (33 aisles x 100m)
  • Steelite Warehouse Expansion - Phoenix AZ (1 aisle x 40m)
  • University of Georgia Library Warehouse Expansion - Athens GA (12 aisles x 62m)
  • DETKI Keksz – Hungary (7 aisles x 27 m)
  • Obo Bettermann - Hungary (17 aisles x 60 m)
  • Prologis - Hungary (5 aisles x 33 m, 3 aisles x 83 m, 8 aisles x 56 m)
  • Helios-Slovenia (8 aisles x 45 m)
  • Nissin-Hungary (5 aisles x 96 m, 1aisles x 70 m, 5 aisles x 31 m)
  • ProLogis Páty-Hungary (10 aisles x 45m)
  • M-Flexilog-Hungary (13 aisles x 36 m, 3 aisles x 28 m)
  • Forest Hungary (3 aisles x 26 m)
  • Yanfeng Hungary (2 aisles x 68 m)
  • Coloplast, Tatabány-Hungary ( 28 aisles x 96 m, 4 aisles x 87 m)
  • UTT warehouse-Hungary (7 aisles x 103.5 m)

For controlling profile quality, every concrete floor falls into one of two categories determined by the type of traffic the floor is intended to support. If the traffic is constrained by guide wires or guide rails to run along specific paths - as in the case of a narrow-aisle warehouse serviced by turret trucks - then the floor is in the Defined Traffic category. Any other type of traffic puts the floor in the Random Traffic category. Fmin applies to Defined Traffic Floors.

Very Narrow Aisle (VNA) Warehousing

Defined Traffic Floors are installed in very narrow-aisle (VNA) warehouses serviced by turret trucks. Operational efficiency in this type of warehousing is determined by the number of pallets handled per truck per hour – which ratio is determined in large part by the flatness/levelness of the tracks in which the lift truck wheels must roll.

The Fmin number sets the maximum cross-aisle (transverse) and down-aisle (longitudinal) ride roughnesses and the mast tilt values to be tolerated

The turret truck manufacturers strive to:

  • achieve higher truck speeds
  • increase truck stability,
  • and reach greater rack heights to increase productivity.

Without a flat and level floor on which to run, however, their efforts are worth nothing. If the floor is too bumpy, the truck will shake too much, and the driver won’t drive the truck at top speed. More trucks will be needed to move the same number of pallets, and the anticipated advantages of the warehouse will be diminished.

The proprietary F-min System - created and controlled by Allen Face - limits the side-to-side and front-to-back tilts, angular velocities, and angular accelerations to be experienced by a hard-axle vehicle of known wheel configuration travelling along its intended wheel tracks.

Limiting Floor Tolerances for VNA Operations

As a consequence, floor requirements have to be well-specified and those variables that affect the truck’s movements must be limited. Unfortunately the gaps under 1, 2, 3, and 4 meter long straightedges are not the variables that influence truck movements. For this reason, the specification formats employed in DIN 15185 and VDMA are not effective.

The six surface variables uniquely limited by Fmin (no other system employs this dynamic simulation approach) control the movements of a truck as it moves across the floor (for more information on the six variables go to ‘Specifier’s Guide to F-Numbers’)

The Fmin System (developed by Allen Face in 1979) is used to control the wheel track profiles on all Defined Traffic floors. Fmin directly limits each wheel track's influence on the truck's angular displacements, angular velocities, and angular accelerations around both its pitch and roll axes. Fmin is thus a full-fledged Vehicle Simulation System that controls both the statics and dynamics of the truck at all locations within the aisle.

Measuring F-min Is Simple

Fmin tolerances have traditionally been measured using a "differential floor profileograph" (invented by Allen Face and his father in 1976). In the spring of 2006 Allen Face developed a special new software package for the D-Meter allowing the instrument - operated by anyone - to generate the same data produced by the profileograph. The D-Meter's accuracy in gauging Fmin was shown to be equal to (even better than) that of the profileograph, and much to the customer's satisfaction, the associated testing and re-testing costs were greatly reduced.

D-Meter employs a sophisticated "grinding optimization" program to compute the minimum amount of grinding required to bring all the wheel tracks into full, 6-dimensional compliance with the specified Fmin number simultaneously.

The actual data collection procedure is clear-cut. The D-Meter is simply marched up and down the future wheel tracks in a fixed pattern to create a complete set of vertically correlated wheel track profiles. These data are downloaded via USB from the D-Meter into a local PC, forwarded to our office via e-mail, and then run through our proprietary Fmin Analysis Software to generate reports that detail the aisle's condition vis-a-vis all six Fmin tolerances at each 30 cm along its entire length and the depth of grinding required at each spot to bring the wheel tracks into full compliance with the specified Fmin.

Contractor’s and Specifier’s Guide to the F-Numbers

The documents in our 'download' section provide a more detailed explanation of the FF/FL and Fmin systems and will help you incorporate these two powerful systems into your floor projects both quickly and easily.

Conv. Good Flat Very flat Super flat Ultra flat
Fmin number 25 38 50 75 100 150
Transverse levelness, mm 8.1 5.4 4.1 2.7 2 1.4
Transverse flatness per 30 cm, mm 3.2 2.1 1.6 1.1 0.8 0.5
Longitudinal levelness, forward, mm 9.4 6.6 4.7 3.1 2.3 1.6
Longitudinal flatness per 30 cm, forward, mm 3.2 2.1 1.6 1.1 0.8 0.5
Longitudinal levelness, backward, mm 9.4 6.6 4.7 3.1 2.3 1.6
Longitudinal flatness per 30 cm, backward, mm 3.2 2.1 1.6 1.1 0.8 0.5
Please subscribe to our Newsletter to get a monthly e-mail with our latest